Victron Smart BatteryProtect - 100AMP - 6-35 VDC - Bluetooth Capable [BPR110022000]
- Product SKU: CWR-82918
- Category: Electrical, Electrical - Battery Management, Victron Energy, Victron Energy
- Order within
Smart BatteryProtect - 100AMP - 6-35 VDC - Bluetooth Capable
Features:
- Protects the battery against excessive discharge and can be used as a system on/off switch The Smart BatteryProtect disconnects the battery from non-essential loads before it is completely discharged (which would damage the battery) or before it has insufficient power left to crank the engine. The on/off input can be used as a system on/off switch.Â
- 12/24V auto ranging The Smart BatteryProtect automatically detects system voltage one time only.Â
- Bluetooth: programming made easy When using Bluetooth to program the Smart BatteryProtect any required engage/disengage levels can be set. Alternatively, one of nine predefined engage/disengage levels can be set with the programming pin (see manual). If required, Bluetooth can be disabled.Â
- A special setting for Li-ion batteries In this mode the BatteryProtect can be controlled by the VE.Bus BMS. Note: the BatteryProtect can also be used as a charge interrupter in between a battery charger and a Li-ion battery. See connection diagram in the manual.
- Ultra-low current consumption This is important in case of Li-ion batteries, especially after low voltage shutdown. Please see our Li-ion battery datasheet and the VE.Bus BMS manual for more information.Â
- Over voltage protection To prevent damage to sensitive loads due to over voltage, the load is disconnected whenever the DC voltage exceeds 16.3V respectively 32.6V.Â
- Ignition proof No relays but MOSFET switches, and therefore no sparks.Â
- Delayed alarm output The alarm output is activated if the battery voltage drops below the preset disconnect level during more than 12 seconds. Starting the engine will therefore not activate the alarm. The alarm output is a short circuit proof open collector output to the negative (minus) rail, max. current 50 mA. The alarm output is typically used to activate a buzzer, LED or relay.Â
- Delayed load disconnect and delayed reconnect The load will be disconnected 90 seconds after the battery voltage drops below the preset level. If the battery voltage increases again to the connect threshold within this time period (after the engine has been started for example), the load will not be disconnected. The load will be reconnected 30 seconds after the battery voltage has increased to more than the preset reconnect voltage.
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
Please contact your dealer for any returns, repairs or support issues related to this product.Quick Guide (pdf)
Brochure (pdf)
Smart BatteryProtect - 100AMP - 6-35 VDC - Bluetooth Capable
Features:
- Protects the battery against excessive discharge and can be used as a system on/off switch The Smart BatteryProtect disconnects the battery from non-essential loads before it is completely discharged (which would damage the battery) or before it has insufficient power left to crank the engine. The on/off input can be used as a system on/off switch.Â
- 12/24V auto ranging The Smart BatteryProtect automatically detects system voltage one time only.Â
- Bluetooth: programming made easy When using Bluetooth to program the Smart BatteryProtect any required engage/disengage levels can be set. Alternatively, one of nine predefined engage/disengage levels can be set with the programming pin (see manual). If required, Bluetooth can be disabled.Â
- A special setting for Li-ion batteries In this mode the BatteryProtect can be controlled by the VE.Bus BMS. Note: the BatteryProtect can also be used as a charge interrupter in between a battery charger and a Li-ion battery. See connection diagram in the manual.
- Ultra-low current consumption This is important in case of Li-ion batteries, especially after low voltage shutdown. Please see our Li-ion battery datasheet and the VE.Bus BMS manual for more information.Â
- Over voltage protection To prevent damage to sensitive loads due to over voltage, the load is disconnected whenever the DC voltage exceeds 16.3V respectively 32.6V.Â
- Ignition proof No relays but MOSFET switches, and therefore no sparks.Â
- Delayed alarm output The alarm output is activated if the battery voltage drops below the preset disconnect level during more than 12 seconds. Starting the engine will therefore not activate the alarm. The alarm output is a short circuit proof open collector output to the negative (minus) rail, max. current 50 mA. The alarm output is typically used to activate a buzzer, LED or relay.Â
- Delayed load disconnect and delayed reconnect The load will be disconnected 90 seconds after the battery voltage drops below the preset level. If the battery voltage increases again to the connect threshold within this time period (after the engine has been started for example), the load will not be disconnected. The load will be reconnected 30 seconds after the battery voltage has increased to more than the preset reconnect voltage.
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
Please contact your dealer for any returns, repairs or support issues related to this product.Quick Guide (pdf)
Brochure (pdf)
Return & Refund Policy
 Thank You for shopping at Shop CDN Marine.
 If you are not entirely satisfied with your purchase, we are here to help you.
Â
 Manufacturer Support
 Before you return your item, many manufacturers have extensive service centers that can support most product issues. If you need help reaching a manufacturer contact us: ShopCDN@cdnmarine.com
Â
Returns
 You have 20 calendar days to return an item from the date you received it.
 To be eligible for a return, your item must be un-opened and in its original packaging.
 You must present the original receipt or proof of purchase at the time of the return.
 We will not be able to accept returns on special order items.
 Return Merchandise Authorization (RMA) numbers are required for all returns.
To obtain an RMA number, please send an email to: ShopCDN@cdnmarine.com
Â
You can make returns right to our to store.
 In-store returns can be made at 303 Brennan Concourse Bayville NJ, 08721. You must have proof of purchase and RMA number prior to visiting store.
Â
 Refunds
 Once your item is received at the store will notify you of its arrival. It will inspected to make sure it meets all return/refund requirements. Shortly after we will be able to notify you on the status of your refund.
 If your return is approved, we will initiate a refund to your credit card (or original method of payment).
 The time frame of when you receive your refund back to your card is contingent on the individual banking/credit institutions and not at the discretion of CDN Marine.
Â
 Shipping
 You will be responsible for paying for your own shipping costs for returning your item. Shipping costs are nonrefundable.
 If you receive a refund, the cost of original shipping will be deducted from your refund.
Â
Â
 Contact Us
 If you have any questions on how to return your item to us, contact us at: ShopCDN@cdnmarine.comÂ
Â